Tacoma Chimney Pros logo

Fircrest, Pierce County

Chimney Sweep in Fircrest, WA

A chimney sweep in Fircrest runs $189 to $449. Where your house lands in that range depends on the roof: a low ranch with a gentle pitch sits near the bottom, while a two-story stack, a steep climb or a second flue pushes it higher. You get the number before the ladder goes up, and it covers the full brushing, the cleanup and a Level I look at the system.

Typical investment

$189–$449

  • Serving Fircrest and the rest of our Pierce County territory
  • $99 plus tax on-site inspection, credited toward an approved quote
  • Usually on the same route as Bonney Lake, Gig Harbor, Puyallup
  • Local crews
  • Licensed & insured
  • Documented work
  • Written quote first

Book an inspection

Book your $99 inspection

$99 plus tax, deducted when you approve the repair

Service
Town

Book your $99 inspection

Pick a real open slot on our crew's calendar — takes about a minute.

  • No payment to book
  • Written on-site quote
  • Photos of every job
  1. 1
  2. 2
  3. 3
  4. 4

Chimney Sweep in Fircrest

Pick a date
October 2026
Su
Mo
Tu
We
Th
Fr
Sa
Open times

Loading open times…

Not sure where to start

What's going on with your chimney?

Pick what you're seeing at your Fircrest home — we'll point you to the right fix.

What we do

Other chimney services in Fircrest

The same crew, the same written quote — for Fircrest homes.

Ranges shown for orientation — the exact figure is written up on-site, after the inspection.

Why Fircrest homes need chimney sweep

Fircrest streets are lined with houses from the 1950s, 60s and 70s, and most of them were built with a brick chimney and an open fireplace. Plenty of those fireplaces are still used for a Saturday fire, even in homes where a gas furnace now carries the heating. Lighter use does not mean the flue stays clean: short, cool fires tend to leave more sticky residue per log than a long, hot burn.

Sweeping a flue that has changed jobs since the 1960s

Census estimates put the median Fircrest house at 1966, and roughly three homes in four here went up before 1980. That places most local chimneys past the half-century mark, with clay tile liners that have been heated and cooled thousands of times.

Heating habits moved on in the meantime. Around 59% of Fircrest households now rely on utility gas as their main fuel, compared with about a third countywide. So when we sweep, part of the job is confirming what the flue actually serves today: an open hearth, a wood insert, or a gas appliance that should never have been vented into a sooty masonry flue without checking it first.

Your chimney sweep in Fircrest: what's included

Every chimney sweep we do in Fircrest includes:

  • Hearth and floor covered, vacuum sealed to the opening
  • Flue brushed its full height with a head sized to the liner
  • Smoke shelf, damper and firebox scraped and vacuumed
  • Debris or nesting material pulled out
  • Level I visual check of the accessible chimney
  • Photos and a short written summary

Signs you need chimney sweep in Fircrest

  • A sooty smell in the room after rain
  • Fires that are hard to start or smoke at the opening
  • Dark flakes landing on the hearth
  • A damper handle that sticks or will not close
  • No sweep on record since you bought the house

Smoke coming back into the room, or a smell that won't go? Book the inspection first.

Book now

Why Fircrest homes need it

On older Fircrest stacks we often find a damper that no longer seals, a smoke shelf buried under debris, or leaves and twigs dropped in through a missing cap. Where a wood insert was slid into the original firebox, the soot can collect behind the insert where nobody sees it. We note each of these with a photo so you know what came out and why.

Soot can hide an old crack from 2001

The Nisqually earthquake of February 28, 2001 measured 6.8 and started deep under Anderson Island, in Pierce County. When FEMA later went through 30,000 damaged homes, a third of them had chimney damage.

A crack that opened then may still be sitting under years of soot in a Fircrest flue. Clearing the liner is often the first time anyone can see the tiles properly, so if the brush reveals a split tile or an open joint, we photograph it and explain what a closer inspection would involve.

Your chimney sweep in Fircrest, step by step

  1. 1

    Set up clean

    Drop cloths go down and the vacuum is sealed to the firebox before any brushing starts.

  2. 2

    Brush the flue

    Rods and a fitted brush run the length of the liner; the shelf and damper get scraped by hand.

  3. 3

    Check what is left

    With the soot gone we can see the tiles, the damper and the top of the stack clearly.

  4. 4

    Report back

    You see the photos on the spot and get a note saying when the next sweep makes sense.

Chimney Sweep prices in Fircrest

What this work is quoted at for Fircrest homes — the exact figure comes from the $99 on-site inspection, credited toward the work.

Chimney Sweep prices in Fircrest — published rates, 2026
ServicePrice in FircrestWhat that covers
Chimney Sweep$189–$449Full flue swept, Level 1 inspection included
Chimney Inspection$99 plus taxLevel 1 visual; Level 2 adds a full camera scan
Chimney ReliningFrom $1,900Full-length stainless liner, sized to the appliance
Chimney RepairFrom $375Masonry repair — brick and mortar, scoped after diagnosis
Chimney Cap Installation$265–$750Stainless cap fitted; multi-flue and custom at the top

Ranges are what these jobs are quoted at in Fircrest. The exact figure is set on site after a $99 inspection (credited toward the job if you go ahead), and you approve it before any work starts.

Clean flue, dry wood, and the burn ban calendar

A swept chimney does not change when you are allowed to use it. Under Puget Sound Clean Air Agency regulations, visible chimney smoke above 20 percent opacity is allowed for no longer than six straight minutes per hour, and the fuel itself must be well-seasoned firewood or a manufactured log, nothing wet or treated.

During a Stage 1 burn ban, open wood fireplaces must stay unlit unless the household has an approved exemption; Stage 2 extends that to certified stoves and pellet stoves. Check the ban status before lighting up on a cold, still evening.

Around Fircrest

Fircrest is a small city that began as the Regents Park subdivision and incorporated as a town in 1925, with post-war homes — a median build year of 1966, about 74% built before 1980.

FircrestPierce County, WA · 47.229, -122.516

Before and after

What the work changes

Illustrations of what each repair changes on a typical chimney — not photos of a specific job.

The local chimney sweep crew serving Tacoma, WA

From booking to done

Four steps, each one on paper — so you always know what happens next.

  1. 1

    Book online

    Choose a genuine opening on the crew's calendar. Confirmation is immediate.

  2. 2

    On-site inspection

    Liner, crown, cap, flashing and masonry examined in order — each finding photographed.

  3. 3

    Written quote

    One document, plain numbers, covering only the work your chimney genuinely needs.

  4. 4

    Work done & documented

    The repair is completed, then handed over with before-and-after photos of every item.

Chimney Sweep in Fircrest — common questions

What does a chimney sweep cost in Fircrest?

Between $189 and $449. A single-story house with easy roof access is at the low end; height, pitch and extra flues move it up. The figure is agreed before work starts.

We burn only a few fires a year. Do we still need a sweep?

Have it checked once a year and swept when there is enough buildup to matter. A light-use fireplace can often go longer between sweeps, and we will tell you if yours can.

Is the Level I check an extra charge?

No. It is part of the sweep. If we see something that needs a closer look, we explain why before anything else is booked.

Get in touch

Book an inspection

Need your chimney checked in Fircrest?

A $99 on-site inspection, a written quote before any work, and photos of every item we touch.

Call (253) 313-7601Book