Bonney Lake, Pierce County
Chimney cap installation in Bonney Lake is priced between $265 and $750. One round flue with an off-the-shelf stainless top is the cheapest case; covering two or three flues, or fabricating a top for an odd chase, lands higher. A cap is a small part, but on the plateau it does three jobs at once: it sheds rain, it keeps nesting birds and fir debris out, and its screen holds embers inside the flue.
Typical investment
$265–$750
Book an inspection
Book your $99 inspection
$99 plus tax, deducted when you approve the repair
Not sure where to start
Pick what you're seeing at your Bonney Lake home — we'll point you to the right fix.
What we do
The same crew, the same written quote — for Bonney Lake homes.
Level 1 or Level 2 as needed; Level 2 includes a camera run through the entire flue
Learn more
Top-to-bottom brushing of flue and firebox under drop cloths, with a HEPA vacuum pulling the dust
Learn more
Loose or damaged brick, open joints and firebox panels repaired
Learn more
A full-length stainless-steel or cast liner, firebox to chimney top
Learn more
Burner, pilot assembly and valve cleaned and adjusted
Learn more
Crown patched, or recast entirely if it can't be saved
Learn moreRanges shown for orientation — the exact figure is written up on-site, after the inspection.
Much of Bonney Lake's housing stock went up around 2000, often with a factory-built fireplace whose flue ends in a metal termination on top of a framed chase. Those terminations are listed parts, and the cap that goes on them has to match the system. Older brick chimneys, a minority here, take a cap that clamps to the flue tile or covers the whole crown.
Bonney Lake's median home was built in 2001. More than half of local households, around 56 percent by Census count, rely on utility gas for most of their heat; county-wide it is closer to one in three.
On houses of that age, the flue under the cap is frequently a metal system, and a direct-vent gas fireplace may have no chimney-style cap at all, only a termination on an outside wall. We identify which one you have before ordering anything, so the part fits the system it protects.
Every chimney cap installation we do in Bonney Lake includes:
Smoke coming back into the room, or a smell that won't go? Book the inspection first.
Book nowWind lifts light caps off, especially in the colder half of the year, and a bent or missing cap is often the reason water suddenly shows up at the fireplace. Tall firs near a roof also drop needles that pile up on the screen until the draft suffers.
Washington's 2021 residential code spells out the screen on a spark arrestor: it must stop anything the size of a half-inch ball, let a three-eighths-inch ball through so the draft is not choked, and lift off for cleaning.
The State Fire Marshal also advises a cap on every chimney. Summer fire safety bans, set by the county fire marshal during dry spells according to Puget Sound Clean Air Agency, are a reminder that embers leaving a flue are not only a winter concern.
We measure the flue, the chase cover or the crown and note what kind of chimney system you have.
For a factory-built flue, we use a cap that matches its listing; for masonry, a clamp-on or crown-mount stainless cap.
The cap is secured so it will not lift in a winter storm, with its screen set at the right height.
We send a roof photo of the new top and flag anything nearby that looked tired, a worn chase cover for example.
What this work is quoted at for Bonney Lake homes — the exact figure comes from the $99 on-site inspection, credited toward the work.
| Service | Price in Bonney Lake | What that covers |
|---|---|---|
| Chimney Cap Installation | $265–$750 | Stainless cap fitted; multi-flue and custom at the top |
| Chimney Sweep | $189–$449 | Full flue swept, Level 1 inspection included |
| Chimney Inspection | $99 plus tax | Level 1 visual; Level 2 adds a full camera scan |
| Chimney Relining | From $1,900 | Full-length stainless liner, sized to the appliance |
| Chimney Repair | From $375 | Masonry repair — brick and mortar, scoped after diagnosis |
Ranges are what these jobs are quoted at in Bonney Lake. The exact figure is set on site after a $99 inspection (credited toward the job if you go ahead), and you approve it before any work starts.
The Buckley 1 NE station, the closest long-term record to Bonney Lake, averaged 48.5 inches of precipitation a year, more than the Tacoma station, and 11.2 inches of snow.
An uncapped flue takes that water straight down to the damper and firebox, where it rusts metal parts and stains the smoke chamber. A cap is the cheapest way to stop it.
Bonney Lake is a plateau city at roughly 580 feet of elevation that grew from 275 residents in 1950 to 22,487 in 2020, on Lake Tapps, with mostly recent homes — a median build year of 2001, about 16% built before 1980.
Bonney LakePierce County, WA · 47.177, -122.187
Before and after
Illustrations of what each repair changes on a typical chimney — not photos of a specific job.
Before
After
Before
After
Before
After
Four steps, each one on paper — so you always know what happens next.
Choose a genuine opening on the crew's calendar. Confirmation is immediate.
Liner, crown, cap, flashing and masonry examined in order — each finding photographed.
One document, plain numbers, covering only the work your chimney genuinely needs.
The repair is completed, then handed over with before-and-after photos of every item.
$265 to $750. Most single-flue caps land near the lower half of that range; multi-flue or custom caps sit higher.
No. A factory-built chimney is a listed system, and its termination cap should come from the same maker or an approved match.
Washington's code sets the mesh size when an arrestor is fitted. We include a removable screen on every cap we install, so it can be cleaned.
A $99 on-site inspection, a written quote before any work, and photos of every item we touch.
