Milton, Pierce County
Relining a Milton chimney costs from $1,900, which buys a stainless steel liner running the whole height of the flue. Four things raise it: a taller stack, a wider diameter for your appliance, an insulating wrap, and old tile that has to be broken out first. Before any of that is proposed, you see the camera footage of your current flue and the fault that justifies the work.
Typical investment
From $1,900
Book an inspection
Book your $99 inspection
$99 plus tax, deducted when you approve the repair
Not sure where to start
Pick what you're seeing at your Milton home — we'll point you to the right fix.
What we do
The same crew, the same written quote — for Milton homes.
Level 1 or Level 2 as needed; Level 2 includes a camera run through the entire flue
Learn more
Top-to-bottom brushing of flue and firebox under drop cloths, with a HEPA vacuum pulling the dust
Learn more
Loose or damaged brick, open joints and firebox panels repaired
Learn more
A stainless cap sized to your actual flue dimensions
Learn more
Burner, pilot assembly and valve cleaned and adjusted
Learn more
Crown patched, or recast entirely if it can't be saved
Learn moreRanges shown for orientation — the exact figure is written up on-site, after the inspection.
Relining questions in Milton usually come from two directions. Owners of older houses find that the original clay tiles have cracked or separated, or that the brick was never lined at all. Owners of newer houses want to put a modern insert into a fireplace whose flue is far too big for it. In both cases a properly sized liner is what lets the appliance draft and keeps heat away from the framing.
Going by 2020 to 2024 Census estimates, just under 2 percent (1.9) of Pierce County's lived-in homes count wood as their chief fuel. For many of those households the question is not whether to burn but how to do it with a safer, cleaner unit.
Under NFPA 211, echoed by CSIA's own Level 2 procedure, two moments in a stove upgrade each call for a Level II inspection: replacing the old unit with one of a dissimilar kind, and getting ready to reline. That camera look is what tells us the size, shape and condition of the flue your new stove will depend on.
Milton lies inside the Smoke Reduction Zone drawn around Tacoma and Pierce County, where running or putting back an uncertified stove or insert has been against the rules from October 1, 2015 onward. Such a unit has to be taken out and recycled, or disabled, unless the owner has no other adequate heat.
The Clean Air Agency describes disabling as snapping the doors off so they cannot be refitted, or holing the firebox. When a stove comes out and a certified one goes in, the liner is the part that has to change with it.
Every chimney relining we do in Milton includes:
Smoke coming back into the room, or a smell that won't go? Book the inspection first.
Book nowThe most common trigger we see in town is an upgrade: someone replaces an old smoky stove with a certified model and learns the new unit's manual calls for a specific flue size. Right behind that are camera inspections that turn up cracked tiles after a chimney fire, and gas furnaces or water heaters left venting into an oversized masonry flue once the old appliance beside them was removed.
No masonry chimney in Washington is meant to go unlined. Section R1003.11 of the 2021 state residential code accepts clay flue tile, tested and listed liner systems, or other approved materials, provided the material resists corrosion and won't crack at up to 1,800 degrees. Separately, R1003.18 wants 2 inches of air between an inside chimney and anything combustible, and 1 inch for one on an outside wall.
Milton spends about 6.8 months of the year in its wetter season by WeatherSpark's count. Moisture that soaks into old brick meets acidic combustion gases inside an unlined or cracked flue, which is exactly the condition a sound liner is meant to prevent.
We record the full length of the flue so you can see the cracks, gaps or missing lining for yourself.
The appliance's installation manual and the flue's shape set the diameter and whether insulation is needed.
From the roof we guide the stainless tube down to the appliance, join it there, then clamp and cap it where it exits.
Once it is connected we check the draft and document the finished system with photos.
What this work is quoted at for Milton homes — the exact figure comes from the $99 on-site inspection, credited toward the work.
| Service | Price in Milton | What that covers |
|---|---|---|
| Chimney Relining | From $1,900 | Full-length stainless liner, sized to the appliance |
| Chimney Sweep | $189–$449 | Full flue swept, Level 1 inspection included |
| Chimney Inspection | $99 plus tax | Level 1 visual; Level 2 adds a full camera scan |
| Chimney Repair | From $375 | Masonry repair — brick and mortar, scoped after diagnosis |
| Chimney Cap Installation | $265–$750 | Stainless cap fitted; multi-flue and custom at the top |
Ranges are what these jobs are quoted at in Milton. The exact figure is set on site after a $99 inspection (credited toward the job if you go ahead), and you approve it before any work starts.
Milton is a hillside city incorporated in 1907 around a sawmill overlooking the Puyallup Valley, with homes with a median build year of 1988, about 35% of them built before 1980.
MiltonPierce County, WA · 47.248, -122.313
Before and after
Illustrations of what each repair changes on a typical chimney — not photos of a specific job.
Before
After
Before
After
Before
After
Four steps, each one on paper — so you always know what happens next.
Choose a genuine opening on the crew's calendar. Confirmation is immediate.
Liner, crown, cap, flashing and masonry examined in order — each finding photographed.
One document, plain numbers, covering only the work your chimney genuinely needs.
The repair is completed, then handed over with before-and-after photos of every item.
Stainless liners start at $1,900. Tall flues, larger diameters, insulation or removing old tile add to the total, which we quote in writing.
Almost always. Inserts are designed to vent through a liner of a set diameter, and an oversized masonry flue will not draft properly for them.
Isolated damage can sometimes be repaired, but widespread cracking is usually better solved with a new liner.
Most single-flue installs are finished in a day once the liner is on hand.
A $99 on-site inspection, a written quote before any work, and photos of every item we touch.
