Milton, Pierce County
A new chimney cap in Milton costs $265 to $750 installed. An off-the-shelf stainless model over a single flue tile lands close to $265. A cover fabricated to span two or three flues, or a stack that needs extra ladder work to reach, lands closer to $750. What you get for it: a flue that stays dry, a chimney that wildlife cannot move into, and a screen that catches embers before they reach your shingles.
Typical investment
$265–$750
Book an inspection
Book your $99 inspection
$99 plus tax, deducted when you approve the repair
Not sure where to start
Pick what you're seeing at your Milton home — we'll point you to the right fix.
What we do
The same crew, the same written quote — for Milton homes.
Level 1 or Level 2 as needed; Level 2 includes a camera run through the entire flue
Learn more
Top-to-bottom brushing of flue and firebox under drop cloths, with a HEPA vacuum pulling the dust
Learn more
Loose or damaged brick, open joints and firebox panels repaired
Learn more
A full-length stainless-steel or cast liner, firebox to chimney top
Learn more
Burner, pilot assembly and valve cleaned and adjusted
Learn more
Crown patched, or recast entirely if it can't be saved
Learn moreRanges shown for orientation — the exact figure is written up on-site, after the inspection.
Milton's chimneys come in every generation, and so do their tops. On older brick we often find a bare flue tile with nothing over it, or a mild-steel cap that has rusted through. Newer houses with factory-built chimneys usually have a manufacturer's cap, but the screen can clog or the whole thing can loosen in a windy winter. We fit the cap to the flue you actually have rather than forcing one size onto every stack.
Census tables for 2020 to 2024 show wood as the primary heating fuel in some 6,700 Pierce County households. For those homes a chimney is in use daily through the cold months, and a blocked or open flue is a real problem, not an annoyance.
The Washington State Fire Marshal reported this September that fire agencies across the state logged six deaths from home heating fires the year before. Its advice for heating season includes a chimney cap alongside yearly inspection and cleaning.
The Puget Sound Clean Air Agency's 2023 summary for Pierce County counted 272 days of good air, 90 moderate and 3 unhealthy. Winter bans are called for the bad stretches, and a Stage 1 ban halts burning in wood fireplaces and uncertified stoves and inserts, plus all outdoor fires.
A cap helps on the days you can burn. With the screen clear and the flue dry, the fire drafts better and sends up less visible smoke.
Every chimney cap installation we do in Milton includes:
Smoke coming back into the room, or a smell that won't go? Book the inspection first.
Book nowIn Milton the call often starts with a sound: scratching or chirping inside the chimney in spring, when birds and squirrels move into an open flue. The other common start is water, dripping onto the damper or pooling in the firebox after a night of heavy rain. Both usually trace back to a missing or failed cap.
According to WeatherSpark, Milton's windier months run from around mid-October to late April, and December is the gustiest of them. A loose cap that survives summer can end up in the gutter by January.
When a spark arrestor is fitted, the 2021 Washington residential code sets its mesh: openings must stop a half-inch ball yet let a 3/8-inch one pass, and the screen must come off for cleaning. Height matters too: brick stacks must clear their roof penetration by 3 feet or more, and top anything standing within 10 feet by at least 2.
We record the flue size, tile height and crown shape so the cap seats correctly and does not block the draft.
Any nest material or leaves sitting in the opening come out before the new cap goes on.
The cap is secured to the tile or the crown so winter wind cannot shift it.
You get pictures of the installed cap and screen, taken from the roof.
What this work is quoted at for Milton homes — the exact figure comes from the $99 on-site inspection, credited toward the work.
| Service | Price in Milton | What that covers |
|---|---|---|
| Chimney Cap Installation | $265–$750 | Stainless cap fitted; multi-flue and custom at the top |
| Chimney Sweep | $189–$449 | Full flue swept, Level 1 inspection included |
| Chimney Inspection | $99 plus tax | Level 1 visual; Level 2 adds a full camera scan |
| Chimney Relining | From $1,900 | Full-length stainless liner, sized to the appliance |
| Chimney Repair | From $375 | Masonry repair — brick and mortar, scoped after diagnosis |
Ranges are what these jobs are quoted at in Milton. The exact figure is set on site after a $99 inspection (credited toward the job if you go ahead), and you approve it before any work starts.
Milton is a hillside city incorporated in 1907 around a sawmill overlooking the Puyallup Valley, with homes with a median build year of 1988, about 35% of them built before 1980.
MiltonPierce County, WA · 47.248, -122.313
Before and after
Illustrations of what each repair changes on a typical chimney — not photos of a specific job.
Before
After
Before
After
Before
After
Four steps, each one on paper — so you always know what happens next.
Choose a genuine opening on the crew's calendar. Confirmation is immediate.
Liner, crown, cap, flashing and masonry examined in order — each finding photographed.
One document, plain numbers, covering only the work your chimney genuinely needs.
The repair is completed, then handed over with before-and-after photos of every item.
$265 to $750. One standard flue is near $265; multi-flue or custom caps, or a difficult roof, move the price up.
A correctly sized cap should not. Problems come from caps that are too small or screens clogged with soot, which we check for.
Gas vents use a termination made for that appliance. We check it, but a masonry chimney cap is not a substitute for it.
Much longer than a painted or galvanized one, which is why we install stainless as standard.
A $99 on-site inspection, a written quote before any work, and photos of every item we touch.
