Gig Harbor, Pierce County
A gas fireplace service or repair visit in Gig Harbor costs $189 to $475. That covers the diagnosis and the tune-up: we clean the burner and pilot assembly, then test the thermocouple or thermopile, the ignition, the gasket and glass, and the vent from the unit to the outside. If a part has failed, it is quoted on top, in writing, before we replace it.
Typical investment
$189–$475
Book an inspection
Book your $99 inspection
$99 plus tax, deducted when you approve the repair
Not sure where to start
Pick what you're seeing at your Gig Harbor home — we'll point you to the right fix.
What we do
The same crew, the same written quote — for Gig Harbor homes.
Level 1 or Level 2 as needed; Level 2 includes a camera run through the entire flue
Learn more
Top-to-bottom brushing of flue and firebox under drop cloths, with a HEPA vacuum pulling the dust
Learn more
Loose or damaged brick, open joints and firebox panels repaired
Learn more
A full-length stainless-steel or cast liner, firebox to chimney top
Learn more
A stainless cap sized to your actual flue dimensions
Learn more
Crown patched, or recast entirely if it can't be saved
Learn moreRanges shown for orientation — the exact figure is written up on-site, after the inspection.
In many of Gig Harbor's newer homes, the gas fireplace was built as a sealed direct-vent box venting through an outside wall or up a short chase. Older houses near the harbor may have gas logs set into what was once a wood-burning masonry fireplace, and those need a different set of checks.
Gig Harbor faces a bay of Puget Sound and grew as a waterfront town: HistoryLink traces its early population to a Croatian fishing community on the west side and Scandinavian settlers at the north end. It took the legal form of a town on July 12, 1946.
On a house that looks out over the harbor, a direct-vent termination on a water-facing wall takes rain and gusts that a sheltered wall does not. We check that its cap is intact and clear, since a vent that cannot breathe properly is a common reason a pilot keeps going out on windy nights.
Where a gas unit vents up through the roof, its termination cap sits in the same needle fall and moss as the shingles around it. OSU Extension recommends thinning nearby trees so more sunlight reaches the roof as the lasting way to keep moss back, and a clearer roof keeps the vent cap clearer too.
The Washington State Fire Marshal's advice for any home heating appliance is a yearly professional inspection. For a gas fireplace under trees, that visit includes a look at the vent top for debris.
Every gas fireplace service we do in Gig Harbor includes:
Smoke coming back into the room, or a smell that won't go? Book the inspection first.
Book nowThe calls we get are familiar ones: a pilot that keeps going out, an igniter that clicks while nothing catches, glass gone cloudy white, a smell when the fire first comes on, or a vent cap outside that birds, wasps or spiders have claimed over the summer. Most are fixed with cleaning and adjustment. A failed valve or control module is a part, quoted separately.
We fire the unit, watch the flame and test the pilot, ignition and valve to find what is wrong.
Burner, pilot, logs and glass are cleaned and the logs set back in their correct positions.
The vent path and the outside termination are checked for blockage, damage and correct clearances.
If a component has failed, you get the part and labor price in writing before it is replaced.
Gas logs set into an old wood-burning fireplace still vent up a masonry flue, and in a wet climate that flue can hold water: a rusted damper clamp, a damp smoke chamber, a crown that lets rain in. NFPA 211 applies its yearly inspection to vents and fireplaces as much as to wood chimneys.
When a wood fireplace is converted to gas, or a gas appliance is swapped for a different type, NFPA 211 lists that change among the reasons for a Level II inspection. That is the moment to find out whether the old flue is dry and fit to carry gas exhaust.
What this work is quoted at for Gig Harbor homes — the exact figure comes from the $99 on-site inspection, credited toward the work.
| Service | Price in Gig Harbor | What that covers |
|---|---|---|
| Gas Fireplace Service | $189–$475 | Annual service and tune-up; repairs quoted after diagnosis |
| Chimney Sweep | $189–$449 | Full flue swept, Level 1 inspection included |
| Chimney Inspection | $99 plus tax | Level 1 visual; Level 2 adds a full camera scan |
| Chimney Relining | From $1,900 | Full-length stainless liner, sized to the appliance |
| Chimney Repair | From $375 | Masonry repair — brick and mortar, scoped after diagnosis |
Ranges are what these jobs are quoted at in Gig Harbor. The exact figure is set on site after a $99 inspection (credited toward the job if you go ahead), and you approve it before any work starts.
Gig Harbor is a harbor town incorporated in 1946, settled early by a Croatian fishing community on the west side and Scandinavians at the north end, on the Gig Harbor bay, on Puget Sound, with mostly newer homes — a median build year of 1998, fewer than a quarter built before 1980.
Gig HarborPierce County, WA · 47.329, -122.581
Before and after
Illustrations of what each repair changes on a typical chimney — not photos of a specific job.
Before
After
Before
After
Before
After
Four steps, each one on paper — so you always know what happens next.
Choose a genuine opening on the crew's calendar. Confirmation is immediate.
Liner, crown, cap, flashing and masonry examined in order — each finding photographed.
One document, plain numbers, covering only the work your chimney genuinely needs.
The repair is completed, then handed over with before-and-after photos of every item.
The service or repair visit is $189 to $475, set by the unit and what it needs. A replacement part, if one has failed, is quoted on top.
Most often a dirty pilot assembly or a weak thermocouple or thermopile. Both are checked on every visit, and cleaning alone often fixes it.
NFPA 211 calls for vents as well as chimneys to be inspected once a year. A yearly service also keeps the glass clear and the flame burning clean.
A $99 on-site inspection, a written quote before any work, and photos of every item we touch.
